Putty Shitrok is a composition based on limestone or dolomite with the inclusion of vinyl polymers and other additives that give unique properties. It has a homogeneous cream-colored consistency. The mixture is completely ready for use, only preliminary stirring is necessary. In some cases, you can dilute the putty with water to obtain a more fluid consistency.
Putty Sheetrock
Putty is easily applied on the plane, forming a perfectly flat surface. Used in the following cases:
- for leveling various surfaces: ceiling, walls, slopes, etc.,
- for filling cracks in masonry, concrete foundation or in plaster,
- for sealing joints between plasterboard sheets,
- for finishing corners,
- for applying the first or top coat,
- for lamination and texturing of various planes.
Technical characteristics of the building material are as follows:
- white or cream color,
- the density is 1.65 kg / l,
- the drying time of the composition is 5 hours,
- the shelf life in closed containers is several months,
- applied manually or mechanically
- applied at a temperature not lower than +13 degrees,
- Available in buckets of 3.5 and 17 liters.
Sheetrock putties have several advantages. These include:
- Ease of application. The composition has such a consistency that makes it easy to apply the material to the surface. Excellent adhesion simplifies the work process.
- The composition is completely ready for use, which saves time on preparation, eliminates the risk of mixing the mixture in the wrong ratio.
- Long drying time of the composition. The remaining putty can be closed with a lid and stored for several months.
- Cost-effective consumption. Due to the special oily consistency, the composition is easy to apply, the number of falling drops is minimized.
- Low shrinkage, which guarantees high-quality finish without further damage, without cracking.
- Compatibility with various materials and substances, which allows you to putty on various surfaces (concrete, brick, drywall) and decorate them in the future with any materials (wallpaper, paints, plasters, etc.).
- Durability. Shelf life is 12 months. If the bucket with the putty was already opened and the composition was used, then in the future you can store the material for several months.
- High quality trimmed planes.
- Reasonable prices.
Application Features
Sheetrock putties can be applied manually or mechanically. In any case, the quality of the finish is of a high level. It is recommended to apply at least two layers on surfaces not glued with fiberglass, and at least three layers when applied to fiberglass.
The drying time of one layer is 5 hours. After this period, you can apply a subsequent layer.
To obtain a perfectly even base, the layers must be sanded with an abrasive mesh with 180 grain. After processing, the surface is cleaned of dust.
As a result of putty treatment, a perfectly smooth and smooth surface is obtained, ready for further finishing.
The composition is compatible with various surfaces, including plasterboard sheets. The finished mixture and its oily consistency contribute to the quick and easy application of the material to the surface.
A few words in conclusion
Thus, the putty of Shitrok is a universal building composition, which allows you to align surfaces from various materials. After processing, all cracks and seams are closed, the planes become even and smooth. The composition is completely ready for use, which saves time on its manufacture. Excellent adhesion and ductility greatly simplify the process of applying the solution.
Key Features Sheetrock APJC
You are already aware that a cream-like mass is ready for use immediately after opening the bucket. The product is usually white with a beige tint. It has a specific smell.
With Shitrokom we can not only putty on ceilings, walls, structure the surface, but also repair joints between plasterboard sheets, cracks, glue gypsum board with each other, trim corners. True, many are of the opinion that Sheetrock is not quite suitable for covering seams formed between plasterboard sheets. Quite an expensive pleasure, and it is better to use Knauf Uniflott - a product designed specifically for this purpose. However, there are those who disagree with this point of view.
Putty of oily consistency, due to which it holds well on the spatula and is easy to apply. When it dries, it becomes quite elastic and prevents cracking.
You can do a simple experiment. If you are working on a ceiling glued with gypsum board, plastered with “Shitrok”, in which holes are cut for the fixtures, then take one of the pieces and separate the drywall from the glass canvas processed by Sheetrock, and then bend the canvas. Even when the angle during deformation reaches ninety degrees, cracks do not form.
The appearance of surfaces treated with "Shitrok" is amazing. They look dense and smooth, which cannot be achieved through the use of Vetonit. Drying is quick. This process lasts from three to four hours. If you approach the grinding of surfaces with all care, then you will achieve the perfect result. Grinding does not cause any particular difficulties. Nevertheless, when using Vetonit, these measures are easier to implement, because the latter is less dense. Choose an abrasive mesh whose grain size does not exceed one hundred and eighty units.
Continuous puttying involves applying APJC in two layers if there is no fiberglass on the surface. When it is used, it is better to apply three layers. Application of Sheetrock on a less dense putty is excluded in order to avoid gaps that can form due to the small thickness of the layer, as well as your excessive efforts.
Important! Do not putty if the indoor temperature has dropped below thirteen degrees Celsius.
Benefits
- Lack of difficulties in use. After opening the bucket, you can immediately get to work. No batch required. Minimum waste. It holds perfectly on the spatula. It is leveled amazingly easy. Minor layer differences.
- Simple grinding process. The result is excellent quality surfaces. Provided that the grinding was done by professionals, and two layers of paint were applied on top, then everything will look perfect.
- Long shelf life. Even if you leave the bucket open for the whole day, the remnants of the “Cheatrock” will not harden.
- Convenience and durability of buckets. However, the seventeen-liter bucket of Sheetrock weighs twenty-eight kilograms, and for some people it is quite difficult to carry.
Analogs
It goes without saying that “Chitrock” has competitors. At least two analogues deserve close attention:
- Shelton (Bau Master),
- Multi-Finish (Knauf).
In fairness, it should be noted: in fact, there are more analogues, but in stores that sell building materials, they are less common.
The compositions mentioned above, judging by the descriptions, are similar in properties and immediately ready for use. As soon as the necessary information about these products appears, we will publish articles about them on our website.
We advise you not to miss new material. We guarantee that it will be interesting and useful to learn about all the intricacies of working with these mixtures.
Properties and scope Sheetrock APJC
Mix Sheetrock APJC is used for continuous filling of walls and ceilings, as well as for structuring surfaces. It can also be used to seal cracks, seams between sheets of drywall, gluing sheets of drywall to each other and finish corners. However, experts do not recommend using Sheetrock for these purposes, due to its relatively high cost in comparison with the KnaufUniflott composition specially designed for these purposes.
As mentioned above, the surface treated with Puttyro putty immediately looks dense and smooth, in contrast to the surface treated with its closest analogue - Vetonit. The drying time of the last layer of Shitrok is a period of 3-4 hours, and with subsequent thorough grinding, it is possible to obtain an almost perfect surface. The grinding process is a little more difficult compared to Vetonit, it is recommended to use an abrasive skin with a grain size of no more than 180.
In case of continuous puttying, it is recommended to apply the composition in at least two layers on a normal surface and in at least three layers on the surface pasted with fiberglass. In this case, Sheetrock is not allowed to be applied over Vetonit or any other less dense putty, since the layers have a small thickness, and when grinding, there is a risk of the formation of "gaps". You should also observe the temperature regime - the temperature in the room where the Shitrok is used should be at least 13 degrees Celsius.
Main advantages and benefits
- Easy to use - opened the bucket and you can immediately start work. The mixture is firmly held on a spatula, easily leveled, differences between layers are minimal, no waste.
- High surface quality and relative ease of grinding.
- A long period of “life” of the composition - when working during the day, Sheetrock does not thicken, and can be used after six months if it is stored in a bucket with a lid closed.
- The warranty shelf life is two times longer than that of Vetonit.
Scope of putty
Finishing putty Chitrok is used as a finishing layer before applying paint or wallpapering. It gives the walls a flat and smooth surface, and also performs the following tasks:
- Elimination of minor cracks and chips on a plastered concrete base.
- Sealing up joints when attaching drywall boards.
- Derivation of angles and straight lines in complex areas.
- Giving surface texture.
Due to the versatility of the use of the composition, the putty is intended for internal finishing work, and also has a number of features:
The versatility lies in applying the mixture both as a finish and when puttying the surface.- Putty Sheetrock is ready for use. There is no need to knead it, but you can immediately get to work.
- The material Shitrok has an oil composition, due to which it is easily and evenly applied to the surface.
- Due to the density and characteristics of the constituents, the layer is even and beautiful, does not require significant grinding or grouting.
- Putty finishing Shitrok is packaged in buckets of 17 and 3.5 liters. Based on the consumption per square meter, you can determine the required number of kilograms of material for work.
- The applied composition dries quickly. As a finishing finish 3-5 hours (1 layer).
- Both a professional and a beginner can work with the material.
The versatility lies in applying the mixture both as a finish and when puttying the surface.The composition and characteristics of the putty
The basis of the filler composition is limestone or dolomite, as well as vinyl acetate polymers. The content of talc, thickening elements and silicate minerals is acceptable. The color scheme is light beige, and the consistency is creamy. Left in a bucket with a sealed lid, putty is stored for several months.
Chitrock putty is endowed with a lot of advantagesthat are revealed during its application:
You can use the mixture immediately after opening the container (bucket).- Easy application of the mixture due to density and concentration, which reduces the amount of time spent and additional cleaning after completion of work.
- Having high adhesion, even when applying several layers, the Puttyro putty adheres tightly to the surface, leaving the high quality of the work done.
- The glued wallpaper, through which flaws and bulges are not visible, demonstrate a smooth surface.
- Shelf life, both open and closed, is longer than that of analogues.
- Material shrinkage is almost absent.
- For Shitrok putty consumption is minimal.
- Ability to work in rooms with any humidity and temperature indicators.
- The material can interact with other compositions during application without losing its properties.
You can use the mixture immediately after opening the container (bucket).Variety of Cheetrok line
On the market of finishing materials has 3 variations, each of which is intended for specific purposes:
Taping Joint Compound. Its role in the decoration is to restore the surface, eliminate cracks, repair joints. The material has excellent adhesion to drywall boards. The resulting thin layer of putty is endowed with excellent strength indicators.- Toping Joint Compound. It has minimal shrinkage, it is mainly used for repeated application on the treated surface. Finishing putty Chitrok is not used for filling joints.
- All Purpose Compound. A universal option suitable for any job. The composition is especially good when creating textures on the surface, the formation of original drawings and patterns. The material is recommended for work in rooms with high humidity, but under other conditions it is also indispensable.
Taping Joint Compound. Its role in the decoration is to restore the surface, eliminate cracks, repair joints. The material has excellent adhesion to drywall boards. The resulting thin layer of putty is endowed with excellent strength indicators.The choice of material depends on the purpose that the master set.
Methods of applying the composition
The initial action before applying the putty will be the preparation of the surface. Usually the material is applied in several layers. The plane needs to be leveled so that there are no sudden changes, to remove the old fraction. Then prime the base with special formulations. Then the bucket opens and, according to the instructions, the contents are thoroughly mixed with a spatula. Next you can start the application work Putty putrok on the plane. When processing joints, the mixture is applied by means of a connecting tape, on which the material is pressed. There are 2 ways:
- Manual - using a spatula and improvised tools to work with the composition.
- Mechanical - carried out using a spray gun with the spraying of material on the surface.
After drying the first layer (about 5 hours), you can apply the second. After some time, it is possible to grout with a fine abrasive mesh for eliminate minor stains and dust.
After the work is completed, do not throw the remaining putty into the sewer, as this can lead to blockage. And the tools involved in the process, it is enough to rinse with running water, without soaking and scraping. The surface should be left for three days until completely dry. The material will give slight shrinkage. After that, you can glue wallpaper or apply paint.
Universal building composition of cheetrok allows you to align surfaces made of different materials. The composition fills cracks and seams, making the base homogeneous and smooth. The material provides excellent adhesion to the plane, and its plasticity makes it possible to perform work quickly and efficiently.
Conclusion
Experts believe that Sheetrock is devoid of any significant drawbacks. She perfectly resists frosts. To store, putty is amazingly convenient. Surfaces are amazing quality. The product is packaged in buckets, which can then be used for a long time to knead mortar, glue, etc.
Of course, for “Shitrok” you have to pay a decent amount. However, do not save. The result obtained is undoubtedly worth the money spent. The only thing that you need to pay attention to is the observance of the production technology and the choice of performers.Remember, everything can be spoiled if you entrust the puttying of the walls and ceiling with unskilled and irresponsible, so to speak, masters.
See photos, get APJC, hire a team of professionals or do everything yourself if you feel confident in your abilities and you are guaranteed a good result.
